#include <hal/pci.h>
#include <klibc/string.h>
#include <lunaix/block.h>
+#include <lunaix/isrm.h>
#include <lunaix/mm/mmio.h>
#include <lunaix/mm/pmm.h>
#include <lunaix/mm/valloc.h>
LOG_MODULE("AHCI")
-static struct ahci_hba hba;
+struct ahci_hba hba;
-void
+static char sata_ifs[][20] = { "Not detected",
+ "SATA I (1.5Gbps)",
+ "SATA II (3.0Gbps)",
+ "SATA III (6.0Gbps)" };
+
+extern void
+ahci_fsexport(struct block_dev* bdev, void* fs_node);
+
+extern void
__ahci_hba_isr(const isr_param* param);
+extern void
+__ahci_blkio_handler(struct blkio_req* req);
+
int
ahci_init_device(struct hba_port* port);
void
achi_register_ops(struct hba_port* port);
+void
+ahci_register_device(struct hba_device* hbadev);
+
unsigned int
ahci_get_port_usage()
{
struct pci_device* ahci_dev = pci_get_device_by_class(AHCI_HBA_CLASS);
assert_msg(ahci_dev, "AHCI: Not found.");
- uintptr_t bar6, size;
- size = pci_bar_sizing(ahci_dev, &bar6, 6);
- assert_msg(bar6 && PCI_BAR_MMIO(bar6), "AHCI: BAR#6 is not MMIO.");
+ struct pci_base_addr* bar6 = &ahci_dev->bar[5];
+ assert_msg(bar6->type & BAR_TYPE_MMIO, "AHCI: BAR#6 is not MMIO.");
pci_reg_t cmd = pci_read_cspace(ahci_dev->cspace_base, PCI_REG_STATUS_CMD);
pci_write_cspace(ahci_dev->cspace_base, PCI_REG_STATUS_CMD, cmd);
- pci_setup_msi(ahci_dev, AHCI_HBA_IV);
- intr_subscribe(AHCI_HBA_IV, __ahci_hba_isr);
+ pci_setup_msi(ahci_dev, isrm_ivexalloc(__ahci_hba_isr));
memset(&hba, 0, sizeof(hba));
- hba.base = (hba_reg_t*)ioremap(PCI_BAR_ADDR_MM(bar6), size);
+ hba.base = (hba_reg_t*)ioremap(bar6->start, bar6->size);
#ifdef DO_HBA_FULL_RESET
// 重置HBA
continue;
}
+ struct hba_device* hbadev = port->device;
kprintf(KINFO "sata%d: %s, sector_size=%dB, sector=%d\n",
i,
- port->device->model,
- port->device->block_size,
- (uint32_t)port->device->max_lba);
+ hbadev->model,
+ hbadev->block_size,
+ (uint32_t)hbadev->max_lba);
- block_mount_disk(port->device);
+ ahci_register_device(hbadev);
}
}
-char sata_ifs[][20] = { "Not detected",
- "SATA I (1.5Gbps)",
- "SATA II (3.0Gbps)",
- "SATA III (6.0Gbps)" };
-
void
-__ahci_hba_isr(const isr_param* param)
+ahci_register_device(struct hba_device* hbadev)
{
- // TODO: clear the interrupt status
- // TODO: I/O-operation scheduler should be here
- // kprintf(KDEBUG "HBA INTR\n");
+ struct block_dev* bdev =
+ block_alloc_dev(hbadev->model, hbadev, __ahci_blkio_handler);
+
+ bdev->end_lba = hbadev->max_lba;
+ bdev->blk_size = hbadev->block_size;
+
+ block_mount(bdev, ahci_fsexport);
}
void
cmd_fis->count = sector_count;
}
+int
+hba_bind_sbuf(struct hba_cmdh* cmdh, struct hba_cmdt* cmdt, struct membuf mbuf)
+{
+ assert_msg(mbuf.buffer <= 0x400000, "HBA: Buffer too big");
+ cmdh->prdt_len = 1;
+ cmdt->entries[0] = (struct hba_prdte){ .data_base = vmm_v2p(mbuf.buffer),
+ .byte_count = mbuf.size - 1 };
+}
+
+int
+hba_bind_vbuf(struct hba_cmdh* cmdh, struct hba_cmdt* cmdt, struct vecbuf* vbuf)
+{
+ size_t i = 0;
+ struct vecbuf *pos, *n;
+
+ llist_for_each(pos, n, &vbuf->components, components)
+ {
+ assert_msg(i < HBA_MAX_PRDTE, "HBA: Too many PRDTEs");
+ assert_msg(pos->buf.buffer <= 0x400000, "HBA: Buffer too big");
+
+ cmdt->entries[i++] =
+ (struct hba_prdte){ .data_base = vmm_v2p(pos->buf.buffer),
+ .byte_count = pos->buf.size - 1 };
+ }
+
+ cmdh->prdt_len = i + 1;
+}
+
int
hba_prepare_cmd(struct hba_port* port,
struct hba_cmdt** cmdt,
- struct hba_cmdh** cmdh,
- void* buffer,
- unsigned int size)
+ struct hba_cmdh** cmdh)
{
int slot = __get_free_slot(port);
assert_msg(slot >= 0, "HBA: No free slot");
- assert_msg(size <= 0x400000, "HBA: buffer too big");
// 构建命令头（Command Header）和命令表（Command Table）
struct hba_cmdh* cmd_header = &port->cmdlst[slot];
cmd_header->options =
HBA_CMDH_FIS_LEN(sizeof(struct sata_reg_fis)) | HBA_CMDH_CLR_BUSY;
- if (buffer) {
- cmd_header->prdt_len = 1;
- cmd_table->entries[0] =
- (struct hba_prdte){ .data_base = vmm_v2p(buffer),
- .byte_count = size - 1 };
- }
-
*cmdh = cmd_header;
*cmdt = cmd_table;
// 预备DMA接收缓存，用于存放HBA传回的数据
uint16_t* data_in = (uint16_t*)valloc_dma(512);
- int slot = hba_prepare_cmd(port, &cmd_table, &cmd_header, data_in, 512);
+ int slot = hba_prepare_cmd(port, &cmd_table, &cmd_header);
+ hba_bind_sbuf(
+ cmd_header, cmd_table, (struct membuf){ .buffer = data_in, .size = 512 });
port->device = vzalloc(sizeof(struct hba_device));
port->device->port = port;
{
port->device->ops.identify = ahci_identify_device;
if (!(port->device->flags & HBA_DEV_FATAPI)) {
- port->device->ops.read_buffer = sata_read_buffer;
- port->device->ops.write_buffer = sata_write_buffer;
+ port->device->ops.submit = sata_submit;
} else {
- port->device->ops.read_buffer = scsi_read_buffer;
- port->device->ops.write_buffer = scsi_write_buffer;
+ port->device->ops.submit = scsi_submit;
}
}
\ No newline at end of file
git://scm.lunaixsky.com / lunaix-os.git / blobdiff